Your Plumbing Crash Course: A Guide to Installing a Bathtub
Your Plumbing Crash Course: A Guide to Installing a Bathtub
Blog Article
Each person has got their own individual way of thinking on the subject of How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Setting up a bathtub isn't precisely brain surgery, but it does need strong plumbing, carpentry, and occasionally, tiling abilities. Changing an old tub with a new one is also a reasonably challenging project. If the old bathtub is readily obtainable, the task can move easily; if you need to open a wall to eliminate the old bathtub and place the new bathtub, the job is a lot harder. In either instance, the project is within a residence handyman's abilities, although you will certainly need a helper to vacate the old bathtub as well as set in the brand-new one. Make certain you have actually qualified on your own for the job and fit trying it. Instead of employing a service provider to take over a halfway-completed job, it is better to consider using one prior to you begin. Opportunities are you may require a professional plumber to make tube links.
This short article will assist you mount a brand-new tub in your restroom if you have actually already gotten a new tub and don't need to alter the arrangement of your previous water system pipes.
Your tools as well as material checklist should comprise the following:
Removing Old Taps
If you need to change old taps with brand-new ones as a part of your installment, after that the first thing you should do is disconnect the water supply. After doing so, activate the taps to drain pipes any kind of water remaining in the system. The procedure of getting rid of the existing taps can be quite bothersome because of the limited access that is typically the situation.
Utilize a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipes to the taps. Have a cloth ready for the remaining water that will certainly originate from the pipes. When the supply pipelines have actually been gotten rid of, use the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this process. Once the taps have been removed, the holes in the bath/basin will have to be cleaned up of any old sealing compound.
Before moving on to fit the new faucets, compare the pipe connections on the old faucets to the brand-new taps. If the old taps are longer than the new faucets, after that a shank adapter is required for the new taps to fit.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will certainly need a plastic port to prevent damage to the thread. One end of the adapter fits on the plastic tail of the tap as well as the various other end gives a link to the current supply pipes.
If you require to fit a monobloc, after that you will need decreasing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next off, place the faucet in the mounting opening in the bath/basin making sure that the washing machines remain in area in between the tap as well as the sink. Secure the faucet in place with the producer supplied backnut. Once the faucet is firmly in place, the supply pipelines can be attached to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with typical tap ports. The former kind ought to be linked to the tap ends initially, tightening just by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have been connected.
Installing the Bathtub
Using both wooden boards under its feet, position the bath tub in the required position. The wood boards are useful in equally spreading out the weight of the tub over the area of the boards instead of concentrating all the weight onto four small factors.
The next objective is to make certain that the bath tub is leveled all round. This can be accomplished by checking the spirit level and adjusting the feet on the bathtub till the level reviews level.
To install taps, fit all-time low of the outermost versatile faucet connector to the proper supply pipe by making a compression join; after that do the same for the various other faucet.
Turn on the supply of water as well as check all joints and brand-new pipework for leaks as well as tighten them if needed. Fill the bath tub and additionally check the overflow electrical outlet and also the regular outlet for leaks.
Ultimately, fix the bathroom paneling as explained in the maker's user's manual. Tiling and securing around the bath tub must wait up until the bath tub has been made use of at least once as this will settle it into its final placement.
Preparing for the Installation
First of all, the sustaining structure provided with the bath ought to be fitted (if called for) according to the supplier's directions. Next, fit the taps or mixer to the bath tub. When fitting the tap block, it is essential to see to it that if the tap comes with a plastic washer, it is fitted between the bathroom and also the taps. On a plastic bathroom, it is likewise reasonable to fit a sustaining plate under the faucets device to prevent stress on the tub.
Fit the versatile tap ports to the bottom of both taps using 2 nuts and olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet with the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. Ensure you utilize all of the supplied washers.
Attach the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath must now prepare to be fitted in its last setting.
Tiling Around the Tub
In the location where the bathroom fulfills the floor tile, it is essential to secure the joins with a silicone rubber caulking. This is necessary as the installation can relocate sufficient to crack a rigid seal, triggering the water to permeate the wall in between the bathroom and the tiling, resulting in difficulties with dampness and feasible leaks to the ceiling listed below.
You can select from a range of coloured sealers to assimilate your fixtures and fittings. They are marketed in tubes as well as cartridges, and can securing voids as much as a size of 3mm (1/8 inch). If you have a larger void to load, you can load it with twists of drenched paper or soft rope. Bear in mind to always fill the bath tub with water prior to sealing, to enable the movement experienced when the bathtub remains in use. The sealer can crack relatively very early if you do not take into account this activity before securing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are also quickly available on the marketplace. It is advisable to fit the tiles utilizing water-resistant or waterproof glue and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I am just very inquisitive about Tools You Need to Install a New Bathtub and I hope you enjoyed the new blog posting. Enjoyed our piece? Please share it. Let someone else find it. Thanks for your time spent reading it.
Toilet overflow? Dial! Report this page